Code Electronic A24 Manuale di Servizio Pagina 3
- Pagina / 120
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
3
2 SAFETY PRECAUTION
Cautions for units utilizing refrigerant R410A
2-2. CAUTIONS RELATED TO NEW REFRIGERANT
Use new refrigerant pipes.
Make sure that the inside and outside of refrige-
rant piping is clean and it has no contamination
such as sulfur hazardous for use, oxides, dirt,
shaving particles, etc.
In addition, use pipes with specified thickness.
Store the piping to be used during installation
indoors and keep both ends of the piping sealed
until just before brazing. (Leave elbow joints, etc.
in their packaging.)
Use ester oil, ether oil or alkylbenzene oil (small
amount) as the refrigerant oil applied to flares
and flange connections.
In case of using the existing pipes for R22, be careful with
the followings.
· Be sure to clean the pipes and make sure that the insides
of the pipes are clean.
· Change flare nut to the one provided with this product.
Use a newly flared pipe.
· Avoid using thin pipes.
Charge refrigerant from liquid phase of gas
cylinder.
If the refrigerant is charged from gas phase, composition
change may occur in refrigerant and the efficiency will be
lowered.
Do not use refrigerant other than R410A.
If other refrigerant (R22 etc.) is used, chlorine in refrige-
rant can cause deterioration of refrigerant oil etc.
Use a vacuum pump with a reverse flow check
valve.
Vacuum pump oil may flow back into refrigerant cycle and
that can cause deterioration of refrigerant oil etc.
Use the following tools specifically designed for
use with R410A refrigerant.
The following tools are necessary to use R410A refrigerant.
Keep the tools with care.
If dirt, dust or moisture enters into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of com-
pressor.
Do not use a charging cylinder.
If a charging cylinder is used, the composition of refrigera-
nt will change and the efficiency will be lowered.
Flare tool
Electronic refrigerant
charging scale
Vacuum pump adaptor
Size adjustment gauge
Gauge manifold
Torque wrench
Gas leak detector
Charge hose
Tools for R410A
Contamination inside refrigerant piping can cause deterio-
ration of refrigerant oil etc.
If dirt, dust or moisture enters into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of com-
pressor.
If large amount of mineral oil enters, that can cause deterio-
ration of refrigerant oil etc.
Ventilate the room if refrigerant leaks during
operation. If refrigerant comes into contact with
a flame, poisonous gases will be released.
2-1. ALWAYS OBSERVE FOR SAFETY
Before obtaining access to terminals, all supply
circuits must be disconnected.
OCH429--1.qxp 07.11.20 9:17 AM Page 3
- SERVICE MANUAL 1
- Outdoor unit 1
- REFERENCE MANUAL 2
- 2 SAFETY PRECAUTION 3
- Gravimeter 4
- [3] Service tools 4
- [1] Cautions for service 4
- Dimension A 5
- Dimension B 5
- 3 FEATURES 6
- 4 SPECIFICATIONS 7
- Longer pipe than 70 or 100 ft 9
- 5-3. NOISE CRITERION CURVES 10
- 5-4. STANDARD OPERATION DATA 11
- 5-4-2. Cooling only 12
- OUTLINES AND DIMENSIONS 13
- Unit : mm<inch> 14
- WIRING DIAGRAM 16
- M-NET ADAPTER 17
- WIRING SPECIFICATIONS 20
- CND/CN01 21
- 8-4. M-NET WIRING METHOD 23
- 8-4-1. M-NET address setting 24
- REFRIGERANT SYSTEM DIAGRAM 25
- High pressure 26
- A Stop C operation 27
- B Cooling D Heating 27
- (PUZ only) 27
- 10 TROUBLESHOOTING 28
- OUTDOOR BOARD LED Display 29
- TEST RUN 30
- Power on indicator 32
- [Procedure] 33
- Beep Beep 34
- Continued to the next page 43
- From the previous page 44
- • Before repair 51
- 10-6. HOW TO CHECK THE PARTS 55
- DC DC250~330V 56
- CC DC15V 56
- T =15exp{3480( 57
- T =7.465exp{4057( 57
- T=17exp{4170( 57
- Linear expansion valve 58
- (A12, 18) 58
- (A24, 30, 36, 42) 59
- <Composition> 60
- 10-8. EMERGENCY OPERATION 62
- 10-9. TEST POINT DIAGRAM 64
- PUZ-A18NHA2 PUZ-A18NHA2-BS 65
- PUZ-A24NHA2 PUZ-A24NHA2-BS 66
- PUY-A24NHA2 PUY-A24NHA2-BS 66
- Outdoor power circuit board 68
- PUZ-A18NHA2 68
- PUZ-A18NHA2-BS 68
- PUY-A12/18NHA2 68
- PUY-A12/18NHA2-BS 68
- PUZ-A30/36/42NHA2 69
- PUZ-A30/36/42NHA2-BS 69
- PUY-A30/36/42NHA2 69
- PUY-A30/36/42NHA2-BS 69
- Active filter module 70
- Under suspension 71
- Pump down Start Normal 71
- Power consumption 72
- (Demand switch ON) 72
- (SW1 on) 73
- Detailed 74
- 1 second 76
- SW2 setting 77
- Display detail 77
- Explanation for display Unit 77
- •The ones digit 84
- EASY MAINTENANCE FUNCTION 85
- 12,340 hours 86
- Waiting for response 86
- Flashing 86
- After approx 86
- 10 seconds 86
- Check Points 87
- 12 FUNCTION SETTING 88
- Mode No.11 89
- Setting number 90
- Mode number 90
- [Operating Procedure] 91
- Setting language (English) 94
- ON/OFF TEMP 95
- 13-2. REQUEST CODE LIST 97
- Refer to 100
- 14 DISASSEMBLY PROCEDURE 106
- OPERATING PROCEDURE PHOTOS 107
- OPERATING PROCEDURE 111
- PHOTOS & ILLUSTRATION 111
- PUZ-A42NHA2 PUZ-A42NHA2-BS 116
Sealey TB63 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Narzędzia Sealey TB63.
Dostarczamy 1 pdf podręczników Sealey TB63 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commenti su questo manuale